Other Resources My Cup of Joe » finishing carpentry? Rss Feed  
Moderators: k9car363, the bear, DerekL, alicefoeller Reply
2018-01-09 1:52 PM

User image

Pro
6838
5000100050010010010025
Tejas
Subject: finishing carpentry?
We replaced flooring in our master bath. It had thick tile and we went with a much thinner flooring material. As a result, the areas around the base of the door frames have a nice gap. Other than caulking, any ideas on filling that gap? I can caulk with the best of them, I just don't think it will provide the finish I'm looking for. Any ideas?


2018-01-10 10:37 AM
in reply to: mdg2003

User image

Extreme Veteran
799
500100100252525
Subject: RE: finishing carpentry?
I had something similar but we went with a thicker tile, so I had to transfer down to the attached hard wood. Check out these to see if something like that would work.

https://www.homedepot.com/b/Flooring-Flooring-Tools-Materials-Transi...
2018-01-10 12:44 PM
in reply to: jmcconne

User image

Pro
6838
5000100050010010010025
Tejas
Subject: RE: finishing carpentry?
It's the door casing that is undercut, leaving a big gap. https://www.casingkickers.com - I found this solution and might go with it.
2018-01-10 3:10 PM
in reply to: 0

User image


1300
1000100100100
Subject: RE: finishing carpentry?
Sight unseen it sounds like shoe base trim is what you are looking for. Quarter round is an example but you can find something nicer depending on the look you desire. Never mind , just realized you were talking about only the door

Edited by Goggles Pizzano 2018-01-10 3:13 PM
2018-01-10 7:22 PM
in reply to: mdg2003

User image

Extreme Veteran
799
500100100252525
Subject: RE: finishing carpentry?
Those look great for what you need to do, if the style matches well enough.
2018-01-12 8:44 AM
in reply to: jmcconne

User image

Veteran
485
100100100100252525
Elmira, ON
Subject: RE: finishing carpentry?
I've been in construction for almost 15 years. Please ignore the above responses. Obvious these people don't know what they are talking about.

First, you need to contact 3 demolition contractors and get prices to tear down your house. Unfortunately, your going to have to start over but I think you already secretly knew that. With demolition complete and a new house being built, be sure not to pick the wrong flooring again when you rebuild. You won't face this issue again.

Problem solved. Glad I could help.



2018-01-12 6:19 PM
in reply to: TheCrownsOwn

User image

Pro
6838
5000100050010010010025
Tejas
Subject: RE: finishing carpentry?
Originally posted by TheCrownsOwn

I've been in construction for almost 15 years. Please ignore the above responses. Obvious these people don't know what they are talking about.

First, you need to contact 3 demolition contractors and get prices to tear down your house. Unfortunately, your going to have to start over but I think you already secretly knew that. With demolition complete and a new house being built, be sure not to pick the wrong flooring again when you rebuild. You won't face this issue again.

Problem solved. Glad I could help.




We've decided to brace up the house and cut it in half at the point where the door casing is too high; we'll then remove the excess material above the floor line.Then we have the slab raised to meet the point where we cut out the excess and then remove bracing. Gravity will close the gap and some caulking will cover any remaining imperfections.
2018-01-19 9:50 AM
in reply to: #5234576

User image


14

Subject: RE: finishing carpentry?
What if you cut off more of the trim from the bottom and put in 6 or 8 inches of flute molding? I've been working all night, so I hope I am saying that correctly and of course it would be after rebuilding the house...
2018-01-19 6:39 PM
in reply to: treanormj

User image

Pro
6838
5000100050010010010025
Tejas
Subject: RE: finishing carpentry?
Originally posted by treanormj

What if you cut off more of the trim from the bottom and put in 6 or 8 inches of flute molding? I've been working all night, so I hope I am saying that correctly and of course it would be after rebuilding the house...


That's an idea I will look into. Thanks.
New Thread
Other Resources My Cup of Joe » finishing carpentry? Rss Feed